• Show All
  • Serie T

Icono_8canalesT
Icono_2400WT
Icono_QuantapulseS
Icono_ClassH2Z

The T Series of amplifiers has been specifically developed for fixed installation and/or network applications. Thus they are equipped with specific connectors: Euro style input and screw terminal barrier strip output, to offer clear, direct and hassle-free connectivity.

Furthermore they offer up to eight independent channels per unit to allow for as many zoning possibilities. Their unitary power output is dimensioned to suit specifically that type of installations.

• Eight and four channel models with 300W and 150W per channel

• Minimal footprint and mass arround 200mm depth and 6 Kg

• Optional Add-on card to interface with third party alarm systems with GPIO connections

• FCM™ Faulty Channel Management system to avoid entire device shutdown

• State-of-the-art layout for maximum performance and reliability

• Highly oversized thermal dissipation design for maximum reliability

• Superb distortion and noise figures

• All channels bridgeable by pairs

• Selectable gain in four channel groups (26, 32 and 38dB)

• Subsonic filter per channel (35Hz user selectable)

• Temperature and signal dependant, intelligent cooling system for minimal noise

• Optimal heat extraction due to the air tunneled enclosure and insulator-less power devices attachment to the heatsink

• Direct connector-less output for maximum quality loudspeaker control

• High grade engineering inside with the latest SMD technology

• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection

• Critical electronic and mechanical parts selection

• Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection

• Detented and optionally tamper-proof volume potentiometers

• Hi efficiency, two steps Class H Audio topology

• Protection, Signal and Clip indicators per channel

• Power On and Standby general indicators

• Extremely compact, fully featured QuantaPulse Power supply

• Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations

• Factory preset worldwide mains voltage power supply

• Laser cut four milimeters aluminium front panel

• Rugged 2U steel chasis

Output Power T604 T1204 T1208 T2408
4 ohm 4x210W 4x415W 8x180W 8x370W
8 ohm 4x140W 4x265W 8x115W 8x210W
Bridge 8 ohm 2x420W 2x830W 4x360W 4x740W
High Z
70Vrms / 100Vpeak - 2x640W - 4x600W

 

• Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz

• Phase Response (@1W 20Hz-20kHz): ±15deg

• Total Harmonic Distortion (20Hz-20kHz): <0.05%

• Intermodulation Distortion (SMPTE): <0.05%

• Crosstalk (20Hz-1kHz): >70dB

• Voltage Gain (selectable): 26/32/38 dB

• Sensitivity: T604: 1.5/0.8/0.4V – T1204: 2.1/1.0/0.5V – T1208: 1.4/0.7/0.4V – T2408: 2.0/1.0/0.5V

• Signal to noise ratio: T604: 107dB – T1204: 110dB – T1208: 107dB – T2408: 110dB

• Required AC Mains (230V AC Mains @8ohm 1/8 rated power): T604: 1A – T1204: 1.5A – T1208: 1.4A – T2408: 2.6A

• Dimensions (WxHxD): 483×88.9×210 mm – 19×3.5×8.27 inches

• Weight (Net): T604/T1204: 5.4Kg – 11.8Lbs         T1208/T2408: 6.2Kg-13.5Lbs

• Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™

At the back of the amplifier are located remote on/off connections to switch-on the amplifier from a third party controller or alarm system. The amplifier power switch must be activated to enter in the stand-by mode, indicated by the corresponding front panel led, being ready for a power-on command from the external circuitry.

Relay contacts are provided too for easy an inexpensive remote monitoring that can be routed to a supervisor control system to switch a spare amplifier or to any other control action.

Newsletter

You will receive information about new products and updates
(C) C.E. Studio-2 sl. RAM Audio and RAM logo are registered trademarks of C.E. Studio-2 sl. Privacy Policy - Design by NearWebs